LM4990 2 Watt Audio Power Amplifier with Selectable Shutdown Logic Level

The LM4990 is an audio power amplifier primarily designed for demanding applications in mobile phones and other portable communication device applications. It is capable of delivering 1.25 watts of continuous average power to an 8Ω BTL load and 2 watts of continuous average power (LD and MH only) to a 4Ω BTL load with less than 1% distortion (THD+N+N) from a 5VDC power supply. Boomer audio power amplifiers were designed specifically to provide high quality output power with a minimal amount of external components. The LM4990 does not require output coupling capacitors or bootstrap capacitors, and therefore is ideally suited for mobile phone and other low voltage applications where minimal power consumption is a primary requirement.

  2 Watt Audio Power Amplifier with Selectable Shutdown Logic Level

The LM4990 features a low-power consumption shutdown mode. To facilitate this, Shutdown may be enabled by either logic high or low depending on mode selection. Driving the shutdown mode pin either high or low enables the shutdown pin to be driven in a likewise manner to enable shutdown. The LM4990 contains advanced pop & click circuitry which eliminates noise which would otherwise occur during turn-on and turn-off transitions. The LM4990 is unity-gain stable and can be configured by external gain-setting resistors.

 Features

Available in space-saving packages: LLP, Exposed-DAP TSSOP, MSOP, and ITL

Ultra low current shutdown mode

Improved pop & click circuitry eliminates noise during turn-on and turn-off transitions

2.2 - 5.5V operation

No output coupling capacitors, snubber networks or bootstrap capacitors required

Unity-gain stable

External gain configuration capability

User selectable shutdown High or Low logic Level
Key Specification

Improved PSRR at 217Hz & 1KHz	62dB
Power Output at 5.0V, 1% THD+N, 4Ω (LD and MH only)	2W (typ)
Power Output at 5.0V, 1% THD+N, 8Ω	1.25W (typ)
Power Output at 3.0V, 1% THD+N, 4Ω	600mW (typ)
Power Output at 3.0V, 1% THD+N, 8Ω	425mW (typ)
Shutdown Current	0.1µA (typ)

Applications

• Mobile Phones
• PDAs
• Portable electronic devices

Datasheets

Source: http://www.ecircuitslab.com/2011/07/lm4990-2-watt-audio-power-amplifier.html

Read More..

LM 390 based on 2 Way Intercom

This is a really easy 2-way intercom circuit primarily based on a LM390 audio amplifier circuit . the intercom circuit is a stand-alone electronic communications system intended for limited or private dialogue. For this circuit youll use a 8 ohms speaker, one for each station and require a vi volts dc power offer. Gain management will be done by capacitively coupling a resistor (or FET) from pin vi to ground.

The LM390 Power Audio Amplifier is optimized for 6V, 7.5V, 9V operation into low impedance loads. The gain is internally set at twenty to stay the external part count low, however the addition of an external resistor and capacitor between pins 2 and vi wil increase the gain to any value up to 200. The inputs are ground referenced while the output is automatically biased to at least one 0.5 the provision voltage.

Read More..

2 X 2 4 2 x 4 5 17 Watt Power Amplifier

Amplifier circuit here is all based on the ic in the gains. Three IC TA7230P, TA7236P, TA7237AP is intregated circuit (IC) which was applied to the power amplifier. Each IC has a different output, different input voltage, all IC TA7230P, TA7236P, TA7237AP is manufactured by Toshiba.

TA7230P, TA7236P, TA7237AP amplifier schematic

Read More..