Rear Light After Glow For Bicycles

This article is of interest only to readers whose bicycle lights are powered by a dynamo. The laws on bicycle lights in the United Kingdom are stricter than in other countries and a dynamo is, therefore, a rarity in this country. From the point of view of traffic safety it is advisable (in UK obligatory) for cyclists to have the rear lamp of their bicycle to light even when they are at standstill.

In principle, it is not very difficult to modify the existing rear light with afterglow: all this needs is a large enough energy reservoir. Since the after-glow is required for short periods of time only, a battery is not required: a large value capacitor, say, 1 F, is quite sufficient.As the diagram shows, in the present circuit, the normal rear light bulb is replaced by two series-connected bright LEDs, D2 and D3. These are clearly visible with a current of only 6 mA (compared with 50 mA of the bulb).

The current is set with series resistor R1. The LEDs are shunted by the 1 F capacitor, C1. Since the working voltage of this component is only 5.5 V, it is, in spite of its high value, physically small. An effective regulator is needed to limit the dynamo voltage adequately. Normal regulators cannot be used here, since they do not work at low voltages. Moreover, such a device would discharge the capacitor when the cycle is at standstill.

Circuit diagram :

Rear Light After Glow Circuit Diagram

Fortunately, there is a low-drop type that meets the present requirements nicely: the Type LP2950CZ5.0. Of course, the dynamo output voltage needs to be rectified before it can be applied to the regulator. In the present circuit, this is effected by half-wave rectifier D1 and buffer capacitor C2. Diode D1 is a Schottky type to keep any losses low – important for this application, because the ground connection via the bicycle frame usually causes some losses as well. The value of buffer capacitor has been chosen well above requirements to ensure that C1 is charged during the negative half cycles of the dynamo voltage.

Source : www.extremecircuits.net

Read More..

Roma has developed a small E17 LED Light Bulb

Roma has developed a small LED bulb "LDA4L-G-E17" can support E17 lamp holder, compare with the original LED bulbs such as 12 volt LED lights, new products reduce the size of the power part, the shade of the hemispherical shape is more nearly spherical. LED light source module use the COB construct without mirror, the shape almost identical to  old-fashioned small krypton bulb to achieve 180°light distribution angle.

Prior to the disadvantage of small LED bulb is less luminous part of the light distribution angle narrow, dark horizontal and supply side. The brightness of the new product is equivalent to a 25W mini krypton bulb. The shade is made of the proliferation of Roma self-developed material that can be issued does not point to the warmth of light. The bulb the total luminous flux of 265lm, the power consumption of 4W. The light color than incandescent light color. Design life (the luminous flux dropped to 70% of the initial time) is approximately 40,000 hours. Pricing is open, expect the actual price of less than 2000 yen.

By the way, I konw where to buy the LED lighting such as LED light and best led flashlight at low price,

Read More..

How to fix a tube light simply

This post shows how to fix a tube light with its parts correctly.lots of people asked me about this that is why I thought to give you some thing like this.now I think you will be able to solve your problems.

Read More..

Automatic Night Light Feeds Directly From the AC Line

There are many approaches to the problem of activating a light when it becomes dark, and a recent Design Idea covers this topic (Reference 1). Some approaches require a dc power supply and an electromechanical relay, but a better approach involves feeding the device directly from the ac line, minimizing the number of components 

(Figure 1).

Figure 1. The photoresistor activates the TRIAC and the load when darkness falls.

The heart of the device is a light-sensitive cadmium-sulphide resistor, PR, with a resistance of approximately 200 kΩ in the dark and decreasing to a few kilohms in the light. PR and capacitor C1 form an ac-voltage divider. In daylight, the voltage across PR is too low to generate the required gate-trigger current to turn on bidirectional ac switch Q1, thus keeping the load – usually a lamp – off. When it becomes dark, PR’s resistance rises, resulting in an increase in the TRIAC’s gate current that triggers the TRIAC and lights the lamp.

The circuit uses inexpensive, off-the-shelf components, including the VT90N1 photoresistor; a 0.1-μF, 275V capacitor; and an L2004F61 TRIAC with a load current of 4A rms, a peak blocking voltage of 200V, and a gate-trigger current of 5 mA. The exact specifications of these components are not critical; you could use others instead.

Editor’s note:
Attributes worth mentioning include the fact that the capacitor introduces a phase shift, which places the peak of the gate voltage close to the zero crossing of the load’s sine wave for optimum turn-on timing. Another benefit is thermal hysteresis, which occurs due to the reduction of the required triggering voltage and current as the TRIAC warms up after the initial turn-on. Link

Read More..